搜索结果: 1-9 共查到“工学 POWER STATION”相关记录9条 . 查询时间(0.062 秒)
RESEARCH ON THE RETRIEVAL MODEL OF HOT-POLLUTING FOR WARMLIQUID LETTING IN NUCLEAR POWER STATION
Nuclear power station Hot-polluting Remote sensing technique Temperature retrieval
2016/3/17
Warm-liquid is discharged at the speed of 100m3/S when the nuclear power station are running, which becomes hot-polluting because of the rising temperature near the shore area.. Thehot-polluting tempe...
Comparison Of Semi-Automatic And Automatic Slick Detection Algorithms For Jiyeh Power Station Oil Spill, Lebanon
Oil spill SAR
2014/4/22
After air strikes on July 14 and 15, 2006 the Jiyeh Power Station started leaking oil into the eastern Mediterranean Sea. The power station is located about 30 km south of Beirut and the slick covered...
The University of Queensland will assist RATCH-Australia Corporation Limited (RAC) assess the viability of converting the coal-fired Collinsville Power Station owned by RAC to a hybrid solar thermal /...
FEASIBILITY STUDY AND ENERGY EFFICIENCY ESTIMATION OF GEOTHERMAL POWER STATION BASED ON MEDIUM ENTHALPY WATER
geothermal power plant low-temperature power plant organic Rankine cycle
2009/10/14
In the work presented are the results of investigations regarding the effectiveness of operation of power plant fed by geothermal water with the flow rate of 100, 150, and 200 m3/h and temperatures of...
田湾核电站循环水泵安装（Erection of Circulation Water Pumps in Tianwan Nuclear Power Station）
循环水泵 中心 间隙
2008/11/19
循环水泵主要是向汽轮机的凝汽器供给冷却水，因此循环水泵安装质量的好坏将影响凝汽器出力，严重时，会引起汽轮机停机事故。田湾核电站四台循环水泵中无备用泵，因此水泵安装质量对机组运行的重要性大大提高。从保证安装质量出发，针对循环水泵安装技术进行探索、总结，并在工程中加以应用和推广。
田湾核电站500 kV SF6封闭组合电器安装（Erection of 500 kV GIS in Tianwan Nuclear Power Station）
SF6封闭组合电器 SF6气体绝缘管道母线 清洗
2008/10/16
总结和介绍了500 kV GIS的安装过程，并提出了改进建议，为今后500 kV GIS安装项目提供借鉴和参考。
介绍了凝汽器拼装的施工特点、施工过程、发生的问题及解决方案。从保证质量、安全、进度出发，对田湾核电站凝汽器拼装技术进行总结，并在工程中加以应用和推广。
核电站技术废物的管理与改进(Management and Improvement of Technical Radioactive Waste in Nuclear Power Station)
技术废物 核电站
2008/10/8
叙述了大亚湾核电站放射性技术废物（主要指维修活动所产生的废物）的主要来源、组成和处理工艺。通过对影响技术废物产生量高的主要因素进行深入分析，找出原因所在，并有针对性地提出一些有效的改进措施。经过2003年现场实践，证明所采取的措施是切实可行、行之有效的，对减少技术废物产生量起到了关键性的作用。
介绍了现场总线控制系统FCS（Field-bus Control System）的发展，以及FCS的结构及主要技术特点。FCS可以实现在线设备可靠性数据采集，使概率安全分析（PSA- Probability Safety Assessment）、风险指引技术（Risk-informed technology）等应用发挥出更大的作用，大大提高了高层管理的准确性和实时性。